Products

Epoxy Floor Coating

937E EPOXY FLOOR ANTI-STATIC SELF-LEVELING FLAT PAINT

Epoxy Floor Anti-static Self-leveling Flat Paint
Download

General Information:

Epoxy Floor anti-static self-leveling paint is based on epoxy resin and alicyclic amine resin as the base material, with advanced pigments and pigments conductive pigments, additives made of two-component finish. With wear resistance, chemical resistance are advantages. High hardness of film, good mechanical strength and wear resistance, permanent conductivity, and uniform conductivity

Suitable Use:

1. Used in indoor cement products or concrete surface wear, dust coating, can handle 100 ~ 1 million level.
2. With Nanpao epoxy primer and in the coating, anti-static surface paint can be used as indoor floor of the anti-static paint

Characteristics:

1. Cured film surface defects, corrosion resistance, chemical resistance
2. Film hardness is high, with good mechanical strength and wear resistance
3. Gloss good, seamless, no crack, impermeable, good adhesion, easy to clean and finishing, the construction has excellent leveling performance
4. Permanent electrical conductivity and uniform conductivity

Specification:

1. Color: many colors to choose from
2. Drying time: Surface dry 12 hours, hard dry 24 hours, fully hardened 7 days (25
°C)
                      Surface dry 24 hours, hard dry 48 hours, fully hardened 10 days (10
°C)
   (Note: the above time is about the value, and will change with the surrounding environment)
3. Viscosity: 90 ~ 110KU (mixed paint 25
°C)
4. Density gravity: 1.25 ~ 1.45 g/ml
5. Available time: 30 min or more (25
°C)
6. Surface resistance: 2.5*104Ω- 1*109Ω (100V) 
(with conductive primer, the surface resistance value will change with the conductive primer resistance value) 
7. Film Appearance: there may be conductive fiber outcrops on the surface
8. Proportion: A : B = 4 : 0.9 (
mass ratio)
9. Recommended painting road: 1 layer
10. Standard dosage: 0.8
± 0.1kg / m2(film thickness ~ 1mm)
11. Coating method: trowel coating
12. Packing:
Base 24 kg/can, Hardener 5.4 kg/can

Directions for Use:

1. Surface preparation:
- The surface should be flat and dry sufficiently
- Remove oil, moisture, dust, paint and other contaminants from the surface to be coated

2. Preparation of paint:
- Stir to be mixed uniformly before use
- Keep correct mixing ratio and add hardener to base

Storage instructions:

1. Valid: 12 months
2. Note: this product must be stored in a cool dry and ventilated place, and avoid direct sunlight, away from the fire

Cautions:

  1. The main substance and the hardener must be proportionally blended, stir evenly the mixture before use. Recommend to use before the pot-life is over
  2. Remove all oil, grease, water, and dust from the substrate
  3. This product is inflammable and should keep away from heat and fire
  4. During the application, the work site should be ventilated and avoid direct contact with skin and eyes. For more information, please refer to MSDS
  5. The ambient temperature must not below 50C or the relative humidity less than 85%
  6. The main substance and hardener should be tightly closed and stored in a cool place when it is in use
  7. Epoxy floor coating direct sunlight may fade away or  discolor but does not affect its role and function
  8. This product must be used with the conductive primer with conductive effect, no use of the anti-static effect.
  9. Construction dosage control: According to the recommended amount of construction, construction is too easy to turn on the amount of construction is too little surface fiber outcrops, affecting the appearance
  10. Before application, A agent should be stirred well with B mixture to prevent uneven distribution of fiber
  11. Note: Keep away from the fire. If you are inadvertently in contact with skin and eyes, rinse more than 10 minutes with clean tap water immediately and seek medical attention immediately. See MSDS

 

 

© Copyright NOROO-NANPAO, All rights reserved 
® NOROO-NANPAO giữ bản quyền nội dung trên website này

Login